Recent content by DuncanDK

Hahaha, that tricky parameter P1

I am absolutely amased by the Suntour NCX seatpost. It's like floating on air instead of a constant jarring up the spine. (I ride in a very upright position on my e-bike). So, a big saddle and a suspension seatpost is my recommedation.

I recommend the freeware smartphone apps, because they don't cost anything. All the apps use your phone's GPS to track/measure the speed. Mine is called GPSpeedKMH, but I guess any speed app will do just fine.

If you do not know the gear ratio and/or number of magnets, the type 100 Into parameter P1. (Remember to adjust wheel size and speed limit beforehand) Then go fo a ride. (And use a gps speed app) If you motor tapers off at 23 km/h, the raise parameter P1 by 10 to 110, and recheck speed/taper...

I can’t calculate the correct number for you. Instead you do as described and go for at spin on your bike and fine tune the number in order to align the motor taper-off-effect

Sorry for the typos. I have “auto correction” turned on... in a different language :-)

1) Chose whatever wheel size that show your speed correct in the display (as Close as possible) 2)Type in 25 km/h or 15 miles/h as speed limit 3) type your “baseline” Into parameter P1. It is gear ration X number of magnetsvin moto 4) the adjust P1 up or down to make the motor tap’er of at...

Here is the link to the thread http://www.pedelecs.co.uk/forum/threads/q100-motor-%E2%80%93-parameter-p1-explained-%E2%80%93-speed-alignment.33072/

Hi I explained parameter P1 in the thread: Q100 parameter P1 explained It’s about aligning the controller perception of the wheels actual speed, with the speed lidt that you have entered e.g. (25 km/h in Europe) Do not be fooled by the original setting, thinking that it is correct. It’s just...

Hi guys In the thread below I explain the use of parameter P1 on Q100/S-LCD3 display. I expect it to be the same on q128 and other motors/LCDs http://www.pedelecs.co.uk/forum/threads/q100-motor-–-parameter-p1-explained-–-speed-alignment.33072/ Sincerely yours DuncanDK

Hi guys In the thread below I explain the use of parameter P1 on Q100/S-LCD3 display. I expect it to be the same on q128 and other motors/LCDs http://www.pedelecs.co.uk/forum/threads/q100-motor-%E2%80%93-parameter-p1-explained-%E2%80%93-speed-alignment.33072/ Sincerely yours DuncanDK

Hi guys In the thread below I explain the use of parameter P1 on Q100/S-LCD3 display. I expect it to be the same on q128 and other motors/LCDs http://www.pedelecs.co.uk/forum/threads/q100-motor-–-parameter-p1-explained-–-speed-alignment.33072/ Sincerely yours DuncanDK

- Parameter P1 is used for speed alignment. Below, you’ll read how I managed to align the actual speed with the speed shown in the display, using parameter P1. I also managed to get the setup to taper off power as intended. I live in Europe, so I chose max 25 km/h on my ebike. First, I got it...

I have e-mailed the customer service in the online shop where I bought the controller and asked them what this plug is used for. They haven’t replied yet. Being of an impatient nature, I posted my question here hoping that one of you would have the answer. I shall follow up on my e-mail to...

The plug meassures in at just sub 5V. It is a constant current and it is not affected by turning on/off lights via the display. (Maybe this is just a matter of finding the correct setting in the LCD-display) Now, I can see that my question actually consists of two... 1) The plug voltage...