Search results

Your bike is set to use thr throttle only without the need to pedal or pas as it’s called that’s why the wheel spins free

Thank you all for the feed back I didn’t think it would raise quite so much debate, to be fair I’ve never pushed my bike to its limit as being disabled I don’t pedal much so just use the throttle, my main point , we’ll answered by all thank you, was is it worth getting a new controller to get...

I’ve not looked at e bikes for a while an my folding Benelli has a 10.4 ah battery and the book says aprox 15 miles range , yet I’ve just seen other folders that have 7 or 7 ah battery saying the will go as far as mine , my bike is a 2018 but I dint think batteries had moved on that much, though...

Please remember that this only happened under load ie when the bike had my 16 stone on it , when the wheel was just lifted off the ground there was no problem at all

Sorry I’ve not had chance to get back out on the bike yet but I’ll post the speed when I do and I’ll have a look at the lcd3 voltage and let you know thanks

If you look back at this thread then you will see it’s a brand new bike , and worked fine but I wanted a lcd3 display and as I was ordering it I got a new controller that’s 15amp, volt , and this ment the only original part was the wheel with the motor in it that was believed to be a Q100 but it...

I’ve only done it to make the bike go as it kept overloading the motor and cutting out , I think as I got the bigger controller and the bike has a little motor they just would not work together so reducing the flow has done the job and if I ever change the wheel and get a bigger motor I won’t...

Ok after a lot of trial and error with the lcd3 settings I found the one that makes the bike go and not cut out as soon as you try to push the throttle to the full , it’s the C5 setting the unit comes with it set at 10 that’s the max , I tried it on a lower setting and found the best was 06 or...

The wheel size just gives you the correct speed of the bike so putting in a bigger or smaller size will only show the wrong speed and not make the bike any faster or slower

Hi I made a similar mistake and you need a sensorless controller it only has 3 wires and 2 power wires not the 5 hall censor ones got mine from here http://www.pswpower.com/peng/iview.asp?KeyID=dtpic-2016-3F-4B8V.50CQQ worth a try all the best

Just want to say thanks for this thread I want to get out on my bike soon to try it but I know from the pas in settings 1 or 2 that the bike runs fine but not to full speed but in 3-5 it can and will cut out , the same with the throttle if I push it slow then all fine but push it full and the...

Thanks chaps that's great as the bike is new I'm not mad on opening the motor, I will start from the control unit with the wiring and double check all connections as there isn't a lot of room in the box under the battery there may be a connection problem when I put it in ill reset the p1 to...

Hi I've tried to upload video but it won't work , I've looked at the problem again and I've got all the settings from the lcd3 and compared them to the standard and can only find problem with my p2 is set to 1 not 0 , the votes seem fine , and as I sad before the noise the motor makes is all...

tried that the screen is on volts and works as you said but the power still cuts out , tried to video it but can't load it for some reason , I'm still of the opinion there is a setting wrong or as one of you previous replays the control unit is to strong at 15a for the motor and I may need to...

Thanks never got as far a screen 2 as the bike cuts out in screen 1 the motor display does as above and that tells me that it may be getting to much to quickly but I will try screen 2 when next on the bike , sadly I can't think what to try next could it be any of the C settings or any other P...

Mine must be backwards as it starts o nill and goes up as I pull away it's the right hand side middle says motor

Sorry, on the display it shows the voltage going up as you press the throttle and as soon as it goes over 30 and it has shown 38 it will cut out and drop to nill , on some settings like p67 it will cut out at 17v, it does feel like it gets to much power to quick but as this never happened before...

The battery is a sealed unit 36v 11.4ah , the problem is just the same on pedal assist, if I build up slowly then it will work fine on throttle or pedal but if I have it in level 5 pedal ass the it cuts out and as I said if I push the throttle full on it will go a bit but as soon as it hits 30v...

So I've been out 2 hours and tried every setting from 30-255 the only ones that helped a bit were 123-125 and around 190 but at no time did it work without cutting power at some point , so now I have a few thoughts, 1 reconnect the 30% power reduction wire it's white , 2 take the wheel off open...

Yes I'll try th p1 setting and get back with results all the best thanks again