Search results

  1. hot_spot

    Bafang bbshd motor not working error code 08

    Hi again guys. the wheel is now sorted and working. there was a blue and yellow wire snapped in the main black cable going down to the small circuit board in the hub.
  2. hot_spot

    Bafang bbshd motor not working error code 08

    i have been asking about on Ebay uk for just a new wheel only and up to now i have been offered one for £260 there is complete conversion kits which are Chinese sellers but are shipped from a warehouse here in the UK. they have much cheaper kits than what the uk guy i mentioned wants for just...
  3. hot_spot

    Bafang bbshd motor not working error code 08

    all the three censers are shaped like the small image that i have drew. plus they all face the same way out words. in the second photo i have just noticed that there is a crack in the out green cable.
  4. hot_spot

    Bafang bbshd motor not working error code 08

    yes but not till after i had put all the hub back together and put the wheel back on to the bike.
  5. hot_spot

    Bafang bbshd motor not working error code 08

    i tried retouching up the solder and sitting the censer better in place, but once all back together again the problem is still there. the new censer that has been put on is a 411F 132 the original ones i think are 63A 905 it was a bit difficult reading them as they must of had some sort of glue...
  6. hot_spot

    Bafang bbshd motor not working error code 08

    well i thought i would decide to take the wheel hub apart and have a look in side. well i wasn't expecting to see that someone has already replaced one of the hall censers. and not a very well done job at that as well. i will have a closer look at the one that has been replaced and see if it...
  7. hot_spot

    Bafang bbshd motor not working error code 08

    i just got 20k from only one phase wire out of the three to the negative on the battery and that was it. no resistance to the wheel turning. the only time that i get a bit of resistance to the wheel is when. i keep my finger on the walk mode button and the wheel starts to make a bit of a...
  8. hot_spot

    Bafang bbshd motor not working error code 08

    when the bike is powered up and you turn the wheel back words. the wheel just turns freely with no resistance to it at all. now doing the meter test as you suggested. i only get one reading on one of the three cable ends coming from the controller. (20.0 solid) that is just from the negative...
  9. hot_spot

    Bafang bbshd motor not working error code 08

    i forgot to mention that this bike has no throttle . it is peddle assist only. the censer for the peddle crank movement seems to be ok by the looks of it. as you turn the peddles a small red light keeps flashing on the censer until you stop pedaling.
  10. hot_spot

    Bafang bbshd motor not working error code 08

    some battery pics. if you need any better ones. just ask.
  11. hot_spot

    Bafang bbshd motor not working error code 08

    i will take some photos....
  12. hot_spot

    Bafang bbshd motor not working error code 08

    i just checked again on the buttons. it was by holding down the plus and the power button together for a few seconds. i checked the voltage on the battery earlier on today and it was giving 43v the battery is the right battery for the bike and the warranty sticker is still on it unbroken. i...
  13. hot_spot

    Bafang bbshd motor not working error code 08

    here is some screen shots of the LCD on the bike. the main screen does stay on from time to time, but then goes off back to the error screen. when the main screen is on. if i hold down the minus button. the the bike goes in to walk mode which shows a little man under neath the bicycle symbol...
  14. hot_spot

    Bafang bbshd motor not working error code 08

    both cable joints at both ends look to be ok to me from what i can tell. i have a multi meter but i have not done any check yet to see if there is any brakes in the wires coming from the controller or the LCD Screen. i did look in the controller box area and noticed that the controller circuit...
  15. hot_spot

    Bafang bbshd motor not working error code 08

    Hi saneagle and thanks for replying to my post. the cables are fine. i am not sure as to when the problem started as i bought the bike second hand. i payed £335 for the bike hoping that it could be fixed. if i have to buy a new wheel. i have just found out how i may of regret buying the thing...
  16. hot_spot

    Bafang bbshd motor not working error code 08

    Hi guys. i have a Lombardo Valderice MTB Rear Wheel Hub motor E-Bike. i am getting the dreaded 08 error code on my LCD display screen. the rear wheel will every now and then give a bit of a jerk and make clicking sounds. do you think the Hall sensors are damaged. if so. how difficult is it to...
  17. hot_spot

    help needed please with powabyke

    i am just thinking. is the controler unit not the original one for the bike? do you think, has the previous owner bought a cheap chinese one hopeing to fix the bike?
  18. hot_spot

    help needed please with powabyke

    Hi b8veh thanks for the reply. you have some great built bikes there, but at my skill level that dosn't help me. i have realized i am missing the battery level light indicator also..
  19. hot_spot

    help needed please with powabyke

    Hi all. i have resently bought a second hand powabyke. i have no idea which modle it is. i was wondering if anyone has the wiring diagrams etc for this bike. someone has been messing about with the controler and it need sorting out. here is some photos of it. thanks in advance.