Menu
Menu
Search
Search titles only
By:
Search titles only
By:
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Electric Bikes
Conversion Kits
EMTBS
eRoad/Commuting
What's New?
Menu
Home
News
Forums
New posts
Trending
Search forums
What's new
New posts
New media
New listings
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
pricer592's latest activity
P
pricer592
replied to the thread
New controller required
.
Thanks to all that helped to diagnose the fault with my ebike , all things we tried failed , so i purchased a cheap old controller and...
Feb 20, 2024
P
pricer592
replied to the thread
New controller required
.
Cleaned the sensor off I think it was fluff rather than a piece of wire , tried the magnet test still the same as in green wire...
Feb 17, 2024
P
pricer592
replied to the thread
New controller required
.
managed to open the pas , whats inside means nothing to me , i guess the 2 black bits are the hall sensors , is there anyway i can do...
Feb 16, 2024
P
pricer592
reacted to
saneagle's post
in the thread
New controller required
with
Like
.
Probably glued together, as the magnet is outside. If you can't open it, it's probably scrap. There is one thing you could try, and...
Feb 15, 2024
P
pricer592
replied to the thread
New controller required
.
I don’t think it can be opened it looks like a sealed unit to me , I will check again and take a picture in morning
Feb 15, 2024
P
pricer592
replied to the thread
New controller required
.
yes the yellow piece comes away from the green piece , picture 1 with the cable , picture 2 clips into the centre of the sensor and...
Feb 15, 2024
P
pricer592
replied to the thread
New controller required
.
I have tested the wires from the pas red wire has steady 4.7v Green wire which I imagine is signal wire from hall ranges 0 to 3.2 v...
Feb 14, 2024
P
pricer592
replied to the thread
New controller required
.
Thanks, I guess by looking at this pic it’s a sealed unit , the magnets clip into the centre and rotate with the pedal , just my luck...
Feb 14, 2024
P
pricer592
replied to the thread
New controller required
.
Can you explain where that hall sensors are please then I can get a picture of them a so have no idea
Feb 14, 2024
P
pricer592
replied to the thread
New controller required
.
Yes that’s correct always works on walk assist , like I say I know sod all about electronics , so following the video on you tube I...
Feb 14, 2024
P
pricer592
replied to the thread
New controller required
.
Thank you for your help this far , I followed a video on the tube this morning along the lines of testing the phases of the controller...
Feb 14, 2024
P
pricer592
replied to the thread
New controller required
.
morning , having opened the controller , all wires seem to be in a connected through blocks to the circuit board , nothing appears to be...
Feb 14, 2024
P
pricer592
replied to the thread
New controller required
.
I will open the controller in morning as I am working until 00:00 tonight , to confirm if the yellow wire is connected or not as it is...
Feb 13, 2024
P
pricer592
replied to the thread
New controller required
.
Regarding the lcd controller there is no adjustments available in the menu at all, I can get into it to change back light and units...
Feb 13, 2024
P
pricer592
replied to the thread
New controller required
.
i wasnt too clear on what i meant last night with the yellow part ,my bad , the inner race was turning not the whole sensor , so i have...
Feb 13, 2024
Top
Bottom