Menu
Menu
Search
Search titles only
By:
Search titles only
By:
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Electric Bikes
Conversion Kits
EMTBS
eRoad/Commuting
What's New?
Menu
Home
News
Forums
New posts
Trending
Search forums
What's new
New posts
New media
New listings
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
saneagle's latest activity
saneagle
replied to the thread
Help!
My next project
.
If you set the throttle like I said with P4 =1 and C4=3, you can use it to give instant max power when you need to pull away quickly...
Jun 23, 2025
saneagle
replied to the thread
Help!
My next project
.
It should handle wheelie good. Why didn't you want to use a downtube battery?
Jun 23, 2025
saneagle
replied to the thread
Help testing Raleigh EVO Controller and cables (Motherboard) after water damage to plugs
.
The ones without the Tranzx system will switch on in that situation, but you can't change anything. Unfortunately, I don't know enough...
Jun 22, 2025
saneagle
replied to the thread
Help testing Raleigh EVO Controller and cables (Motherboard) after water damage to plugs
.
That part sounds OK then. You should only measure voltage from ground (black) to any other pin, not from red downwards to any other pin...
Jun 22, 2025
saneagle
reacted to
Waspy's post
in the thread
Help!
My next project
with
Like
.
The label on the motor looks good to me. Similar to my homemade label for my Mxus motor. As far as I'm aware a factory ebike should...
Jun 22, 2025
saneagle
replied to the thread
Help!
My next project
.
The law just says that the bike has to be marked with the maximum assisted speed. How you do it doesn't matter. From memory, the correct...
Jun 22, 2025
saneagle
replied to the thread
Help testing Raleigh EVO Controller and cables (Motherboard) after water damage to plugs
.
40v fully charged is a bit low, and would indicate something wrong with the battery. It should be close to 42.0v. If the LCD connector...
Jun 22, 2025
saneagle
replied to the thread
Help!
3 pin battery mount - help needed
.
That plate and the rail normally come with the battery and the bit with the plug on can be moved to another plate. You have three pins...
Jun 22, 2025
saneagle
replied to the thread
ADO Carbon
.
In that case it'll be fine except on downhills, where you have to freewheel because you can't pedal fast enough unless you have a...
Jun 22, 2025
saneagle
replied to the thread
More Seizures
.
That's probably because you live in a sports biking area. It won't be the same in the centre of Köln or München.
Jun 22, 2025
saneagle
replied to the thread
Disabled cyclist; with one bad choice behind her, needs help with a new bike
.
I thought we already established that a a system with torque multiplication was unsuitable for her. Why do we keep going round and round...
Jun 22, 2025
saneagle
replied to the thread
ADO Carbon
.
How much power you need and whether you need gears or not depends on your weight and the type of hills you have to climb, and also...
Jun 22, 2025
saneagle
replied to the thread
More Seizures
.
I think the main difference is between people using their bikes for utility and those using them for sport. You're seeing people using...
Jun 22, 2025
saneagle
replied to the thread
.Whine from Ampere
.
Sounds like a stuck clutch. Turn the bike upside down, get a lump-hammer and whack the tyre tangentially in the forward direction until...
Jun 21, 2025
saneagle
replied to the thread
Disabled cyclist; with one bad choice behind her, needs help with a new bike
.
The two requirements of high power and lightweight are conflicting characteristics. It's not that somebody's missing a market, it's...
Jun 21, 2025
Top
Bottom