Search results

. Hi Nealh, Checked my C1 settings, its now running correctly (On Stand) for some reason the initial numbers - 1,2. didn't sort the problem. So as you reminded me about C1 numbers are 0- 7, the only number that worked was 7... I've yet to road test. So fingers crossed its now OK.. AGAIN! Bob.

. Hi Nealh, I'll try the other C1 numbers today. My settings paper only had 1 & 2, scribbled down for C1

Hi Nealh, Thanks for your response. I did press C10 Restore system, earlier in the investigation which may have been the start of this problem ? I have been putting the settings back to some scribbled down settings I made a few years ago. So think the settings are not correct. It may be just one...

Hello all, Not been on here for some time as everything has been going OK. I have the relatively old Display ..KT-LCD3. Issues 1st started when I attempted to switch from KPH to MPH. At first it would not run, (I must have pressed something I shouldn't) finally got it running . But it just...

Sorted... KT-v12L PAS sensor, Kapput! after 250 miles.

Tried the C10 reset but didn't save the setting properly so it didn't reset. I've started to think could it be the pedal Crank sensor ?

The only instruction that came with the kit for the KT-LCD3 was a small 4 page Pamphlet with basic display info. totally inadequate for settings.

Hello again everybody, Got another problem, related to my previous thread. (slowing walk speed down). In the end there was no option but to switch to Km/ h on the KT-LCD3 display. Which involved alot of "unnecessary"messing with the settings Doh !. Which worked well Hanging from the Garage...

One more thing While I'm on Here.....Can my controller that came with the 250W kit (26in Wheel), Handle a 350W Motor? I was thinking I would swap my Kit over to My 27.5 inch MTB . Then Purchase a 27.5 inch wheel with a 350W motor to a few Quid ?

Hi All, It would appear from all messages I've received that it is not possible to change the walking pace speed, Its 6 & stuck with it!... so just set the KT-LCD3 to KPH, walking pace is now 6 KPH. My Heart & I can keep up with that.

I see what your thinking but I'sure its 6MPH....6KPH (under 4MPH) would be much easier.

I think your correct. the question is can this be changed if in mph? I suspect Not from the reply's.

I assume walk speed of 6 is the same in MPH & KPH, if it is possible to change this value to say..5 or 4 I could keep it on MPH. I feel sure the speed setting of 6 is the same in MPH & KPH.

Hmm, interesting thought. It should be as "factory" 36v not touched anything in that area.

Hi Andy, I'm not worried but if its not possible to change The MPH push pace then I'll change it to KPH, but would prefer to change if possible. I like my max speed, Running speed, Trip & odometer in MPH. Regards, BH.

Hello All, I find pushing my ebike up steep hill too quick at 6 mph. the only way I can think to do would be to change MPH to KPH making walking speed 6 KPH, but everything else will be in KPH.(not ideal) Can I change the speed parameter for walking Speed? Ta BH.

Ta vfr400, I'm not on here regular enough to remember how to do the basic actions. BH.

Started a thread a couple of weeks ago about my motor cutting out every 3 or 4 seconds. But cannot find it, may be I didn't post it correctly. But I think I've solved the issue (hopefully) ... The removable motor side casing on the inside has a centre 2 mm thicker bearing boss with "fingers"...

Hello all, its been a while since I've had any problems, mainly because I haven't been on my bike much. Recently decided to service the hub motor check the wiring is OK after replacing the Hall sensors & lube the planetary gears also add another torque bar to the other side of the forks. All...