Search results

Everything works on an Ebike I have except the PAS. Looking at the controller the wires are in the order red green yellow. Does this seem to be in the right order, with red the +5V, Green the signal, and Yellow the Ground. ( Controller is a KT36ZWSRT-EP03 )

Does anyone have a 9 pin Male / Female Julet extension cable? You get one with some Yosepower wheel kits. I need a couple of them for a bike I am building at the moment. Managed to buy one on line, but it needs me to solder 9 wires together to join up into one cable...

i want to make up some wiring extension cables with the JST connectors. I have the JST plugs etc, I just need 2,3,4 wire cable. Red black, red black white, etc. Had a search on amazon, closest I can find is alarm cable that is four strand with black outer. Is there a special name for these type...

Anyone have any news on this company, no reply from emails today, no answer on telephone, Facebook page not updated since March 2017 and Twitter since February. Have they also gone out of business, or just not easy to contact?

I am needing a replacement controller for my bike that has a 36V 250W brushless hub motor. The controller needed is a Kunteng brand, and if possible KT36ZWS HDSLCD. And no, I don't want to wait a month for it to arrive from China, there must be somewhere in the UK that sells them ( excluding...

Has anyone ordered from this company https://www.electricbikeconversions.co.uk Any feedback on the service as they don’t answer emails over the last four days.

Yes, before you all tell me, I should have place a support under the cover while trying to put the bearings back into place. I now have a cracked case cover, that in turn means a motor I can’t use. Does anyone have a dead motor with the same casing that they would let me have as a replacement?

Does anyone have a recommendation for a replacement controller for a Raleigh Velo Cite, or can recommend a online dealer in the UK who can sell me one?

I have almost worked out the wiring for my controller, but not 100% certain it is right. Do you know if I have the correct connections? I also have three wires from the battery connector that I am not sure where they go. Bike is a Raleigh with the battery on the rear pannier with a front hub...

I have a 36 Volt battery ( MOTO70R Li 36V 10Ah ) that is not charging. When pressing the check button on the battery it shows just a red light, and none of the greens light up. When I take a reading with a voltmeter it shows 34.6 volts. The battery has been left sitting uncharged for quite a...

I have two Raleigh Velo Cite bikes, both of which were bought from the same dealer at the same time. So I am told by the person I bought them from. They look identical, and I have found something missing on the controller for one bike. There is no HALL connector on the controller. They both...

I have almost worked out the wiring for my controller, but not 100% certain it is right. Do you know if I have the correct connections? I also have three wires from the battery connector that I am not sure where they go. Bike is a Raleigh with the battery on the rear pannier with a front hub...

Does anyone have the instructions for the LCD display for a Raleigh Velo Cite bike? Photo of the one fitted to my bike incase Raleigh changed their minds at some point.

U

i have had my rear hub grate it's gears when moving off and I was suspecting I might be missing some teeth on the gears. After opening the hub up I was happy to see all the teeth looked good, but it looked a bit dirty and dry inside. I cleaned the gears with a citrus degreaser and a toothbrush...

Hi I am setting up a LCD KD21C on my bike and the bike works, and the display is on, but it does not show speed or distance traveled. I think that this has to do with a setting under the Speed Sensor Option where I need to enter the number of magnets in my motor. A 36V 250W rear hub motor...

I have just replaced the complete electrics on my ebike with only the 24V 250 watt Currie motor and the battery being from the original bike. The new components 24V 250W Electric Bike eBike Controller kit, Panda ECO from Pandaebikes...

Hi, I am trying to find out what is burning out a component on the control unit for a Izip Skyline Electric Bike. The unit was replaced and it did the same thing on the new one. The type of control unit is shown top right circled in yellow and the burnt out components are circled in red.