Search results

  1. D

    PAS WIRING HELP PLEASE

    I have started the process of wiring my pas directly in to my integrated controller solely for the purpose of making it look neater. I purchased the pas separately and has different coloured wires to the wired cable which I will be removing. The controller has black(marked G), red(marked TH)...
  2. D

    Battery new self-build bms issue

    Looking for some help again please. I finally got the courage to build my own battery. It all went well and has been a great learning experience. I wired in my second bms this evening as I thought I blew my first one. I followed the suppliers wiring diagram but I’m getting almost full pack...
  3. D

    Lacing 27.5 wheel with q128c motor

    I intended lacing a 27.5 inch wheel with a q128c motor. Should I be using a 2x or 3x pattern. Are 13g spokes best to use. Many thanks for any advice.
  4. D

    Samsung 18650 Li-ion LiNiCoMnO2

    Just a quick question. Are these a good quality cell? Thanks.
  5. D

    8 to 12 magnet PAS

    I’m looking to change my pas from 8 to 12 magnet one. Can I simply change the disc with the magnets or do I need to replace the sensor part too? The existing one has a waterproof connector which are quite a bit more expensive than the ones with a normal connector. So I was just going to buy a...
  6. D

    Damaged kt-lcd3 screen

    Hello. It appears that I may have damaged my screen. I was testing my motor hall sensors and I think I put the probe from my fluke somewhere I shouldn’t have. The screen comes on when I press and hold the power button but will not stay on when I let go. I was just wondering can they be...
  7. D

    Q128 motor swap

    Hello I received a replacement motor hub from Bmsbattery as the original failed after 200kms. I think I can just disassemble both hubs and swap the internal parts rather than re-lacing the new hub into the wheel. Does anyone know if the 9 pin waterproof connector will pass through the axle or...
  8. D

    Q128 motor strip down

    Hi. I’m looking for help in relation to the above please. I’m getting info 3 fault code, motor hall signal abnormality. Does this involve stripping down the motor? If so, does anyone have a guide? Many thanks Dave Sent from my iPhone using Tapatalk
  9. D

    KT LCD 3 throttle settings

    Hi guys. Just a couple of questions in relation to the above. Is there a way in settings to reduce the delay between operating the throttle and when it actually kicks in? It’s seems to be a second or so currently. Is it possible to reduce the power delivery from the throttle? I’m just...
  10. D

    Battery storage/charging

    Hi there. Just looking for some advice please in relation to battery storage. I purchased two rear hub ebike kits from Bmsbattery recently which I keep away from home. I know this isn’t the practice but they will be left unused, probably, for two months at a time. They will be used daily for a...
  11. D

    PAS TYPE DIFFERENCES

    Hi there. Could someone enlighten me as to the different types of PAS sensors and which type of bottom brackets they can each be used with. Thanks. Sent from my iPhone using Tapatalk
  12. D

    KT LCD 3 POWER SETTINGS

    Is it possible to adjust the power settings on this display? I find that I’m getting too much assistance on settling 1. Settings 4 to 5 seem ok. Thanks. Sent from my iPhone using Tapatalk
  13. D

    Hi there

    just joined. Hoping to learn and help if I can.
  14. D

    Conversion kit advice

    Hi there. I’m looking for advice or help on choosing a kit/components to convert my aluminium hard tail mtb with 26” wheels. The bike weights 14kgs and I am 76kgs. It would be mainly used for a 40km(total) commute here on the relatively flat roads in the south of Spain. However, there is a 14km...