Search results

Hmmm how is this diffrrent from what I have allready done? I rode with a GPS and changed p1 until they showed the same. I kept the bike at 30 km/h but it seemed to be correct at other speeds as well?

What's your experience with this wheel and KT controller? What settings did you use?

Aikema web page doesn't have any of the more technical details of the hub, I'll try emailing them as well as yose power. I tried setting P1 back to 86 and P2=0 and that resulted in a reported max speed of about 40 km/h but the actual speed was about the same as before with P1=86 which was about...

Yes, It's got the same settings as with the old hub. I can reach 550w at high resistance and ~20 km/h but above this the power drops until it stops assisting at all at about 32-33 km/h.

I did my first commute with the new hub today. I'm a bit disappointed actually. The new motor is slower, has less power, especially above 20 km/h and seems to consume qiute a lot more battery power. With the old motor I felt that I had full power until the last 2 km/h before top speed where it...

I'll have to do soke digging about that. With trial and error I landed on p1=161. This gives me accurate speed verified by GPS and top speed of about 34 km/h.

It's currently set to 86. Increasing it, also increases top speed. Is it safe to set to a really high value or do I need to find the exact figure where the speed didn't increase anymore by trial and error? I have no idea what the gear ratio might be...

@Nealh I just swapped the wheels but kept everything else on the bike as is including the KT controller. I'm maxing out at 20 km/h both in throttle and assist. Any suggestions on what setting to change?

Yes, you're absoloutley right. Something to think about if this hub lacks access to spare parts as well. Front hub feels a bit wrong for me though...from time to time there's quite a lot of ice and snow here in Sweden and it feels safer with the motor on the rear wheel in these conditions. Also...

Sounds good. Is the new brand of motors Lishui as well as the controller? Since I've had a lot of problem with my cassette cover (picture below for reference) for my old wheel I'd like to to buy a couple of replacements right away...

I just ordered a new 350w rear cassette wheel and I hope I can use this with my KT controller and LCD3. Are there any settings that need to be changed in the controller with this new wheel? (My old wheel is yose power from 2019)

This has gotten to the point where the pawls are constantly slipping. On my original cover plate it says "CZJB" which is a motor manufacturer but they need to know the model of the motor to help me with a spare part. Yosepower (believe it or not) can't find the information about which model of...

Perhaps this can illustrate. This is the old hub motor cover and my present one sounds worse. This can't be solved by changing any of the visible bearings.

Don't think so, I changed these just a couple of months ago. Well, I changed the first one after about 5000km and got a new one from yose power under warranty. That one started to slip when pedeling, especialliy in weather below freezing. I could sometimes go thru several revelations on the...

Anybody know where I can buy this spare part? It's the cassette holder and motor cover for the first generation yose power 350w kits (rear). Apparently they have changed supplier and don't supply these anymore. Mine is acting up for the second time but I have no idea on where to get it. Anybody...

Since I don't have any spare and the bike is my commuter to work I hoped it would solve itself by just leaving the bike in the sun for a couple of days. As I rode it to and back from work. It's been getting worse and worse so I guess that did not work :) I will buy from yosepower since they...

Good advice, thanks!

Finally my KT LCD3 display or the control buttons have failed. I rode in heavy rain the other day and now I have a hard time using middle and bottom buttons resulting in the bike being almost unusable (since I've managed to hit "0" assist a couple of times). I'm up to 10 000km on this kit now...

A big thank you to you both! I had no idea it was this easy:) the main bearing on the housing was totally shot. The nylon gears looked almost like new and the grease wasn't hard or anything? On another note, I changed the freehub like 1000km ago, the bearing in this one are already a bit worn...

Great, thanks! I will give this a try.