Menu
Menu
Search
Search titles only
By:
Search titles only
By:
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Electric Bikes
Conversion Kits
EMTBS
eRoad/Commuting
What's New?
Menu
Home
News
Forums
New posts
Trending
Search forums
What's new
New posts
New media
New listings
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
Latest activity
What's new
New posts
New media
New media comments
New profile posts
Latest activity
saneagle
replied to the thread
Hello, thinking about a conversion kit
.
That's a perfect bike for converting. I wouldn't get a Swytch kit for your circumstances. They have a front motor, which is the worst...
Jul 9, 2025
S
Sparksandbangs
replied to the thread
Hello, thinking about a conversion kit
.
You would need to be able to take a wheel off. Then adjust the gearing to make sure it runs with the new hub and wheel. It will also...
Jul 9, 2025
N
NoGearNoIdea
replied to the thread
Hello, thinking about a conversion kit
.
Ha! Yes. Thank you for your comment. The option then would be to not bother at all. I mean, change a tire was an extreme example as...
Jul 9, 2025
Waspy
replied to the thread
Hello, thinking about a conversion kit
.
The two main suppliers of kits preferred on this forum is Woosh Bikes and Yosepower. However, if you cannot even change a tyre (no...
Jul 9, 2025
saneagle
replied to the thread
New bike
.
All hub-motors are exceptionally quiet if you use a sine wave controller. Depending on which version of the E-mate you have, you...
Jul 9, 2025
M
matthewslack
replied to the thread
New bike
.
No personal knowledge of any of them, but searching for 'emtb hire south east England' gives a fair number of places. You need a range...
Jul 9, 2025
saneagle
replied to the thread
KT controller, KT LCD3 and pass - guide on working modes
.
It's a waste of time doing anything with the pedal sensor while the throttle isn't working properly. You should disconnect it it until...
Jul 9, 2025
Nealh
replied to the thread
KT controller, KT LCD3 and pass - guide on working modes
.
P2 will typically be value 01 for most hubs as prettymuch most of them use only one magnet for sensing , however if the odo reads very...
Jul 9, 2025
Nealh
replied to the thread
KT controller, KT LCD3 and pass - guide on working modes
.
Does the PAS red LED blink on/off as the magnets pass the sensor? With that type of sensor head positioning/cable tieing in place is...
Jul 9, 2025
P
pinnaboy
replied to the thread
New bike
.
Thanks for that, I tested a Woosh Bear some years ago and liked the torque and I think it was quiet. Is the noise from my ten year old...
Jul 9, 2025
M
matthewslack
replied to the thread
New bike
.
Too far south for me to know. There's a shop in Keswick, plenty of Lakes up and down in easy reach, but that's probably too far north...
Jul 9, 2025
Nealh
replied to the thread
New bike
.
The emate hub likely needs a little service , bearings wear and greasing can be a bit thin on the ground.
Jul 9, 2025
P
pinnaboy
replied to the thread
New bike
.
Thanks for both of the above comments. I did once test ride a Woosh Bear and was very impressed with the torque of the front hub (and I...
Jul 9, 2025
N
NoGearNoIdea
posted the thread
Hello, thinking about a conversion kit
in
Introduce Yourself!
.
So back from a trip away, I've been inspired to push forward with a thought in mind of converting my 2013 Specialized Sirrus to...
Jul 9, 2025
M
matthewslack
replied to the thread
New bike
.
If your riding is not going to change then the type of bike doesn't need to. Mid-drive comes into its own as the off road gets more...
Jul 9, 2025
Top
Bottom