Recent content by jerrysimon

  1. jerrysimon

    eBrompton Build

    This is my wheel. On the TopBikeKit website it says their motor is 1.6kg which is impressive. Are they quiet ?
  2. jerrysimon

    eBrompton Build

    I hope I am not hijacking this thread just say :confused: I use to post several times every day on this forum for years when I was learning this stuff. If you are interested here are my Tongxin 36v, 180w, 260RPM, 28h motors. Not sure if you can still get them. They are only three wire not hall...
  3. jerrysimon

    eBrompton Build

    If you want to learn how to build wheels then 16/20" is the place to start. Plenty of youtube howtos and info on line. Small wheel builds are easy. I had to learn as 13 years ago it was impossible to get anyone to do electric hub builds for Brompton/small wheels. Radial makes it even easier...
  4. jerrysimon

    eBrompton Build

    Looking again at SJSCycles it appears some Brompton rims are only suited for rear/hub builds and as the spokes are crossed I guess that is why the angles are more and thus the holes drilled at an angle. They specifically say not for front wheels/two speed rear wheels or radial built wheels. As I...
  5. jerrysimon

    eBrompton Build

    Last post today ;) We use to use these which are single walled but obviously now you can get better double walled ones for the Brompton. Back then all Brompton rim holes were drilled straight whereas now, for the rear at least, I think they are drilled at an angle...
  6. jerrysimon

    eBrompton Build

    When we first built them we use to lace them up 1X but soon realised that radial lacing was sufficient (strength wise) for such small wheels. This also made the spoke angle and building more managable/simple :) As you can see on the wheel in the front of the picture (black Brompton) this was a...
  7. jerrysimon

    eBrompton Build

    All I recall (is was 13 years ago) the ones provided ready built from China use to have a generic 16" rim that had an ETRO of 305 whereas the Brompton rims are ETRO 349. The other challenge back then was the motors only came with 36h so could not be laced into a standard Brompton rim which was...
  8. jerrysimon

    eBrompton Build

    Yes on my 100mm hubs from memory, I think they are around 118mm. Radial builds are quite easy just lace up, bring up to tension and then work round keeping the rim straight and circular as you can. Loads of youtube videos show you how :)
  9. jerrysimon

    eBrompton Build

    The eletric hub will be much larger than the stock one, so very unlikely.
  10. jerrysimon

    eBrompton Build

    Probably Lithium Polymer which I used a lot in RC Flight (super light) but prefer safer Li-Ion cells on an ebike. Mine are built into both the older and newer Brompton rims which is not difficult for radial builds, as long as you get the spoke length correct :)
  11. jerrysimon

    eBrompton Build

    Meant to add in Cambridge (very flat) I get between 10-15 miles depending on wind. If I go further I just carry a spare. The motor is only 180w so not power hungry, draws less than 5-6amps max and mostly when I am pedaling less than a couple of amps. The solution would not meet requiments of...
  12. jerrysimon

    eBrompton Build

    All my electronics go in one back pocket of the Brompton bag and the battery in the other (it just fits). This keeps everything light, the main bag empty.and means you can carry Brompton in one hand and bag in another :) We had all the same issues you have found buying ready made up wheel sets...
  13. jerrysimon

    eBrompton Build

    There you go :) Good quality/safe Li-Ion Samsung Cells with a BMS built in. You'll need a charger and make some kind of connector (mine is also fused) as shown. Made by Spear & Jackson. These are from an older model lawnmower sold by Argos. I have four purchased off ebay as lots of the lawn...
  14. jerrysimon

    eBrompton Build

    Li-Ion. Hold on I will take a photo and post.
  15. jerrysimon

    eBrompton Build

    Years since I posted here but nice to see people still converting Bromptons. I was one of the first on here using a lightweight Tongxin (almost silent) motor sourced and shipped from China in 2010. I'm retired now but the steel one is still going strong. I now use prebuilt 4Ah 36v lawn mower...