Search results

OK thanks, sounds good. Any recommendations for controller / display?

Thanks very helpful! :). I have a 36V battery lying around, so i might just use that. Can you recommend any specific kits i should go for with the Q100c or Q128c, or are all the kits pretty much the same?

Maybe the bafang cst is more suited?

Oh ok, yes i see. Thanks :). Maybe an option of it does not conflict to much with legs. Btw those are not footrests :)

I think i have misunderstood what a freewheel is. Can you suggest a motor which is suited?

Hi, thanks for the recommendation. I am a bit confused as to where this footrest should be placed, care to explain or visualize on the picture? Currently the feet are one on each side of the weel on the orange "brackets"

Hi, so i will probably be doing some custom fitting, but i was thinking one of these 3 places marked by arrows (on rear axel, on bacside og seat or use the two "side" frames :)

Hi, so i have been reading alot of threads here on hub kit recommendations, but since many of these kits seems to have their pros and cons which very much relates to things such as rider weight, terrain etc. I am looking for some guidance. First of all, because i am in a wheelchair my bike...

So I was going to try Mike's suggestion, but now the display was just constantly on, lighting up in all segments of the display. So i decided to open up the display to look for signs of water or loose connections. It appears that there are 6 "spring loaded" connections in the display, so when...

Hi again Ok so i have not been able to identify any broken cables and it is not tight at the display end. I have uploaded a video of the behaviour. PLease check it out

Thanks d8veh, allways on the spot to help me. I will try all three of your suggestions

Hi Mike Thanks, I will try that :).

Hi I have installed a TSDZ2 with the VLCD5 display on my girlfriends bike. The bike has been riding ok for a while. But now I have some issues with the display. When i turn it on it will of just light up, maybe be blurry/unclear on the digits and text it is displaying and then it will turn...

Ok so found a bad connector. The wire to it was almost corroded away. So I cut the wires, found some new connectors (had some high voltage DC outdoor solar panel connectors lying around), soldered etc. Now the bike runs like a charm again. Thanks for the help and patience :)

Hello d8veh Thanks for your patience and thorough explanation :). I get your point. I will check solder joints, connections and fuses and make sure they are proper for large currents

Ok so just to understand: Thesis is, that when peddling, voltage from battery to display is being interrupted, which causes the display to shut off and motor not to assist? So if I put battery on bike, have bike lifted off ground, peddle (maybe apply resistance to wheel) and measure voltage to...

Hi yeah, thanks! So i measured voltage from battery to display all the way and i cannot find any problems. I will have to try and measure this also when someone is pedelling the bike, to see if it drops out. Battery is china, so could be crap. However it passed my ~350W load test with the 4ohm...

OK so took me some time before i got it testet, but here are my results: Without load I measure 41V on the battery (it's a 36V 12.8Ah). I put a 4 Ohm 150W power resistor on the battery for short period. Voltage on battery only drops to 39V. My guess would be that this is not a problem, and...

Hello Thanks for sound advice. What is lvc? Low Voltage? I have not been able to find anything in manual about system reset, but I will browse ze interweb. Hopefully I will have time wednesday to work on the bike. Can try to measure the voltage display reads.

Hi I have the TSDZ2 350W version with VLCD5 display. Bought it this summer for my GF. Has done about 1000 km. But now we have run in to a problem. The motor will not assist and the display turns off as soon as she starts pedalling. If the assist is set to lowest (off) on the display, it...