Search results

Finally got my test bike on the road. Previously i have only ever had a Woosh SWX02 kit, never noticed the temperature of the controller as its built into the battery. However my new setup is as follows KT 15a controller 48v 7ah battery 36v 250w bafang hub labelled G020.250 36v Bafang - no...

I have the 48v SWX02 Woosh kit (2 years old). Plug and play, only done 300ish miles but its been perfect with no issues. Everything plugs in and works as it should. The controller is built into the battery so its a very neat installation. I cant really tell you much about the range as i pedal a...

Excellent information Appreciate the help

Hi I have a spent a few hours on the settings of the KT LCD3. Searching the internet trying to make sense of it all. I have the following kit Bafang G020.250 code 13 27.5” wheel 48v 7ah battery KT 15a controller Push throttle I will add a pas when I get a chance. I have set the wheel size...

Haha brilliant. I dished the wheel last night. Wheel in bike with tyre and at correct pressure. I have got it pretty much in the middle now. I have trued it again. Seems good to me. I don’t have a spoke tension meter. How can I tell no spokes are really lose apart from the ping test...

Here is a picture of another wheel I have. Looks central compared to the other. Clearance near enough the same top, bottom and both sides I think I may have messed up doing the truing on the other wheel.

Yes the gaps look a lot bigger in the pictures then they really are. The non drive side I did mess up a bit but the axle is in properly. I did use a file to get the axle into the drop outs.

I think I will give the dishing a go. Do I remove all washers from the axle before doing this? Why has the wheel got different clearance from the top and bottom on the same side?

Measured the dropouts 135mm 10 speed cassette. Removed the washers and started again to see where i may have gone wrong. I forgot to take photos but i think i may have removed more material from the non drive side dropout to get the axle to fit. Hence the wheel more towards one side. See...

I will remove the wheel and measure the dropouts and take a better photo as above as soon as I get time.

Appreciate the advice. I had never trued a wheel or replaced a spoke before. I did one last week, took a few hours but it is pretty simple, just need patience. I wouldnt mind giving the dishing a go with the wheel mounted in the bike. I think i will go back to the drawing board. I am going...

Its a 2014 Boardman MX Comp Hybrid, i havenever measured the dropouts but i assume they will be 135. Your 100% correct, adding washers to the non drive side did push the caliper away from the mount so i had to add 3mm washers behind the disc.

I should have mentioned it’s a cassette hub G020. The wheel is more towards the non drive side. I would have to loosen the non drive side spokes and tighten the drive side ones. What I’m wondering is what is an acceptable amount of dish? By how many mm?

I tried 3mm washers before the disc goes on and now it lines up perfectly. However the wheel is still not centred as I thought. Am I better of dishing it?

Hi guys To get the rear hub motor wheel to fit centrally in the frame I need to add 10mm washers to the non drive side. Firstly I’m pretty sure stretching the dropout 10mm on one side won’t cause the aluminium frame any issues right? Secondly doing the above moves the brake calliper away...

They sold out the same day I’m afraid from what I know. The link also seems to have disappeared.

Thanks for the advice!

Many thanks for the help guys. It is one of them cheap wheels from sportsdirect. Few threads about the motor. I am just buying the bits now. Not in a rush.

This is the plug on the motor. I was just weighing up the options but will be getting the lcd3 I think. I don’t know if I want to go for the waterproof kit or the normal plugs where they can be cut and soldered to make the wires shorter and neater.

They finally got back to me with a very simple. “This controller won’t work with your Bafang motor” With my limited knowledge. My wheel has a 9pin plug. I understand these are all standard so the kt controller should work with the lcd3 for example. Am I right?