Search results

Thanks and I surprised myself with so much perseverance and a scowling wife in a small living room . As I said not total perfect cos throttle had gone to low power but unless u have some ideas I can live with that and just use it fir standing start . Thanks for sticking with me .

Yeh I know . But this definitely wasn't restricted before .it seems like it works for first part of twisting throttle. Then does nothing when you twist further I had drop out and motor stopped . Eventually fixed by replacing sensors . But throttle not same now . Not big prob.mainly use pedals...

SORTED !! In the end it was my poor soldering and one of the the hall legs was not connecting properly to the board. So almost complete success. I'm glad I stuck with it . Thanks all Not complete success cos throttle doesnt work well. It responds but not fully . Very slow not full speed , but...

Sorted ! In the end it was my poor soldering and one of the the hall legs were not connecting properly to the board. So almost complete succes

It's mike ref voilamart . The motor is definitely working . With the motor cover off. But as soon as put the cover back on its stopping it from working . There's something obvious wrong here only not obvious to me . May I ask a couple of questions as you have a voilamart. 1. I have the...

Not sure cos other bike is original giant motor and controller . But it did run as I said off the wheel constantly and it did run constantly on the wheel on the bike fir 200 yards then stopped . So everything was ok initially after I replaced halls

Oh and it does respond to the throttle with a jolt . So is your test not necessary . That being the case I don't know what to do next . So unless any ideas I have to give up

Hi wheezy.thanks . Before I check what you suggest just want to mention that the motoe was tested without halls and didn't react at all. Then I changed the sensors cos the incorrect ones had been fitted . Once I put new ss41s it ran and it ran constantly while under test. But when I put it...

I've been repairing this motor with some great help on this forum . I checked cables and MOSFETs . Then discovered I needed to replace all 3 halls . I did that and the motor ran again . But when I put all back together it ran ok for 200 yds then stopped . I then noticed it pulsed briefly when...

Wheezy , Maybe you guys have left this thread but just realised that the motor kicks in when you turn the wheel then goes off so thinkin that one of the halls maybe stopped working . It did run for 200 yds so somethin happened after that. I've seen how to test hall sensors from controller end...

, Maybe you guys have left this thread but just realised that the motor kicks in when you turn the wheel then goes off so thinkin that one of the halls maybe stopped working . It did run for 200 yds so somethin happened after that. I've seen how to test hall sensors from controller end putting...

Sorted that's how it should be . I couldn't remember. But see my other posts bike stopped working again after 100yds. If it's nothi g obvious I'm giving up

A Apparently 3 lights is normal on fully charged according to previous owner I just couldnt remember

Think that was just not sitting totally home at first

Old halls weren't too bad bit if glue which I melted . But sadly it's stopped working again so unless I see something obvious I had enough and selling for repair . But wheezy you have voilamart . So the 3 lights on the on off battery indicator are now all on at the same time . Does that mean...

Well gentlemen one Giant suede for sale for repair. It's stopped working again so could be minor short touching on movement and then of course retesting MOSFETs and halls . So unless I see something obvious I had enough . but as a matter or interest all 3 lights are now showing on on off...

Yeh with hindsight shoulda replaced them first despite suspect cables etc . For what they cost if theyd blown

I have a problem refitting motor back into wheel . I hope you recognise this any if you with voilamart . its making a scraping noise and jamming when I turn the wheel ( manually ) after I put the cover back on . I can't see why it's happening . anyone plz help . I think you have voilamart...

Halls fitted motor running Thank you all gentlemen fir your patience and support. Fir whatever reason the incorrect hall sensors stopped it from workin