Search results

Hi, the one that I needed was one with one plug at the controller end, then LCD, Throttle, 2 x Brake and light at the other end. Mine had a fault on the throttle side and Joey from Yosepower in Germany is sending me replacements this week. It would be great if there was a place on this site...

Hi, Thanks for the tip. I managed to order a cable the correct length from a company in Sweden, so one the weekend mine will be taken off the bike, and the new one installed. When I joined the wires, I spread the wires apart so they looked like a upside down volcano, then when pushing the two...

Hi Sturmy, the P2 setting is based on the specs I found for my motor, which is a 250w 36V Bafang Fun8 unit. I cut and pasted the info into my spreadsheet. I understand this is the number of magnets. Tried your option and made no difference. I think it’s a dud cable, so will have another try on...

Hi Sturmy. Found that there is no signal on one line of the three from the throttle. I don’t have any sharp bends on my routing. I am on your advise check the one place where I have a cable clamp firmly holding a cable in place. As it’s on an extension cable I can bypass it to find out if...

Hi, I am guessing the fault might be with the cable, there are not to many setting variations on the LCD. Online I found a cable, but not in this country. So I have ordered a couple of cables, the four to one and also a spare controller to motor cable. 3 days and it should be here. If the...

Hi PC2017. No error messages showing up, and I have tried the motor running under PAS and then thumbing the throttle, no effect from the throttle. Sent from my iPad using Tapatalk

I did make up a extension cable yesterday from the controller to the motor, and the motor runs fine, and each wire tested good from each end. if I remove the extension and connect the original leads together from controller to motor it still runs the same. All the other cables look in good...

C4 to 2, no result. ( sounds a bit like chess ) Sent from my iPad using Tapatalk

I have a Yosepower kit that I have just put onto a bike. Before I routed all my cabling and I had everything joined up, the throttle worked fine, as did the PAS. After putting the bike all together, thePAS works, and the throttle does not. The controller is a KT with KT LCD3 screen, and all...

Hi Dom, take a look at this one from the same company I bought mine from. https://www.ebay.co.uk/itm/48V1000W-26-Rear-Motor-Freewheel-E-Bike-Hub-Conversion-DIY-Retrofit-Kit-Black/302923802323?hash=item4687aa66d3:g:chYAAOSwx2Fbxped Order was placed on Thursday, and it arrived on the following...

Hi, I spliced all 9 wires this afternoon, and managed to keep it all neat and tidy. I saw the cable you mention. But don’t have the patience to wait till January for a cable to arrive. Thanks for taking the time to look online. Sent from my iPad using Tapatalk

Hi Neal, Yorkshire Tea, and logic in the end wins the day. Sent from my iPad using Tapatalk

Thanks for the help, made up a new connector from one with the closest colours, and decided that black is ground, then yellow must be ground on the controller. Plugged it in and waved a magnet near it caused the wheel to spin. Sent from my iPad using Tapatalk

Here’s the controller end Sent from my iPad using Tapatalk

Hi, just gathered up a few more Pass units. Here’s a new one that has brown yellow black. Sent from my iPad using Tapatalk

Hi, I have two here, One is yellow, red, blue Second is Red green black Sent from my iPad using Tapatalk

Everything works on an Ebike I have except the PAS. Looking at the controller the wires are in the order red green yellow. Does this seem to be in the right order, with red the +5V, Green the signal, and Yellow the Ground. ( Controller is a KT36ZWSRT-EP03 )

Does anyone have a 9 pin Male / Female Julet extension cable? You get one with some Yosepower wheel kits. I need a couple of them for a bike I am building at the moment. Managed to buy one on line, but it needs me to solder 9 wires together to join up into one cable...

Hi Quackstar, hope your Yosepower build went okay! I received my front hub kit this week, and I am building to bikes at the same time. The wheel I am using on one bike and the controller and cables on another. Now I have a small problem, in that the wheel I am using has a shorter cable on it...

Replying to Pete, yes I always try and support local, and around York there are some brilliant small bike shops and engineering companies that restore my faith in the human race. As someone who has worked in the hospitality field for 35 years, I find sloppy customer service unacceptable, and do...