Search results

  1. Andrew Wingrove

    New controller for 2012 Raleigh Velo Cite

    I am planning on sending it back this weekend. I have taken a look at the one on eBay. The one I bought came with a LCD, so it should not have been a problem adding the generic throttle and PAS. Seems a pity to buy the whole set when I already have two working PAS units and 2 working throttles...
  2. Andrew Wingrove

    New controller for 2012 Raleigh Velo Cite

    Hi Andy, thanks for responding. My setup is 36V, The motor is a Brushless 36V 250W with 5 hall sensor in front wheel. my original controller was model KT36ZWS-HDSLCD I bought a controller online this week, A Brainpower model kslzv83. I tried setting it up and all I could get from it was three...
  3. Andrew Wingrove

    New controller for 2012 Raleigh Velo Cite

    Does anyone have a recommendation for a replacement controller for a Raleigh Velo Cite, or can recommend a online dealer in the UK who can sell me one?
  4. Andrew Wingrove

    LCD S866 + Brainpower controller

    I have a Brainpower controller that I am trying to fit to my bike at the moment. The LCD is marked as Model LCD S866. My motor does not have a white wire running from it, only the red,black, green blue yellow. Can I leave it disconnected? And is the throttle connecting to Red black blue on the...
  5. Andrew Wingrove

    Controller help needed

    Good morning and thank you for your answers. It was cold in the garage and I was rushing things, silly mistake, but must move on and do better next time. I have two sets of cables stripped from a second identical bike, so I have one set still in the bike I am fixing, and the second set on my...
  6. Andrew Wingrove

    Controller help needed

    I have almost worked out the wiring for my controller, but not 100% certain it is right. Do you know if I have the correct connections? I also have three wires from the battery connector that I am not sure where they go. Bike is a Raleigh with the battery on the rear pannier with a front hub...
  7. Andrew Wingrove

    Hall Connector

    Thank you for your answer. The bikes have only done about 40 miles each from new, and the controllers were the ones in the bikes when they were purchased. Perhaps it was the dealer who did the swap, or the Raleigh factory though that no one would notice. But good to know that its not vital as I...
  8. Andrew Wingrove

    Battery Voltage

    I only wish I knew. I am trying to re connect my controller and the controller does not seem to have an inputs for it. Yes, I know I should have marked all the cables before unclipping them. See attached charts to follow my wiring plan. And I don't seem to have a Male three pin JST...
  9. Andrew Wingrove

    Battery Voltage

    As you know your batteries, can you tell me what this 3 wire JST connector with blue green and red wires would be doing connecting to the three outputs on my battery between positive and negative? This picture is the behind where the battery connects too and holds the controller unit.
  10. Andrew Wingrove

    Battery Voltage

    Thanks, I will keep it on charge overnight and see where it ends up.
  11. Andrew Wingrove

    Battery Voltage

    I have let it charge for a while and I am getting 39.2 volts from the battery now. Is that too high, or does that sound about correct?
  12. Andrew Wingrove

    Battery Voltage

    You clever chap! I had two chargers and the one I was using had the green light on, but nothing outputting at the end. Tried the other one and had 41V. Plugged in into battery and now have one green light on the battery. Thank you. Could you please have a look at my other posts today, you...
  13. Andrew Wingrove

    Battery Voltage

    I have a 36 Volt battery ( MOTO70R Li 36V 10Ah ) that is not charging. When pressing the check button on the battery it shows just a red light, and none of the greens light up. When I take a reading with a voltmeter it shows 34.6 volts. The battery has been left sitting uncharged for quite a...
  14. Andrew Wingrove

    Hall Connector

    I have two Raleigh Velo Cite bikes, both of which were bought from the same dealer at the same time. So I am told by the person I bought them from. They look identical, and I have found something missing on the controller for one bike. There is no HALL connector on the controller. They both...
  15. Andrew Wingrove

    Motor Controller Wiring Challenge

    I have almost worked out the wiring for my controller, but not 100% certain it is right. Do you know if I have the correct connections? I also have three wires from the battery connector that I am not sure where they go. Bike is a Raleigh with the battery on the rear pannier with a front hub...
  16. Andrew Wingrove

    Raleigh Velo Cite

    Before anyone replies, I have now found it in the manual for Pedago Electric bikes at https://pedegoelectricbikes.com/wp-content/uploads/2018/09/pedego-master-owners-manual.pdf
  17. Andrew Wingrove

    Raleigh Velo Cite

    Does anyone have the instructions for the LCD display for a Raleigh Velo Cite bike? Photo of the one fitted to my bike incase Raleigh changed their minds at some point.
  18. Andrew Wingrove

    This showed up on Facebook This morning. eBikes for £89.00 Frame: RN Frameworks Aluminum w/ Powderco

    But that I might have missed in the above, Drive: Bosch Performance CX 250W (75Nm) Battery: Bosch Performance PowerPack 500Wh. Clearly to good to be true, so can’t be true.
  19. Andrew Wingrove

    Rear hub greasing

    Hi d8veh, I did not take the bearings out. Considered it, but as I did not have any new bearings at the time, decided not to add to the task for the day of adding some grease. The black grunge was the original grease I found, and the white is the new Lithium I was using after giving it a clean...