big thanks to peter @performane line bearings

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
it was always the plan to put the cx motor on this thing and peter made it happen and 24hr postage as well :cool:

got it on in 30 mins and can feel the extra 15nm that the cx motor puts out than the 60 from the performance motor.

DSC_0123_03.JPG

old motor on the box and new one installed, felt a bit stiff at first but can take about 150 miles to bed in the motor bearings but should keep this thing going for another 6 years :p

not bad for a 2014 haibike with 3 miles on the clock :cool:
 
Last edited:

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
time for a look inside the old motor and still looks like new :p

DSC_0124_03.JPGDSC_0125_02.JPG

all it needs is a bit more grease and good to go :cool:

old pics, but that nylon gear has taken a hammering nothing last forever but done its job over the years but is on it last legs and surprised i not snapped any teeth of it the speed i go :eek:

DSC_0114_01.JPG

DSC_0115.JPG
 
Last edited:

Nealh

Esteemed Pedelecer
Aug 7, 2014
19,991
8,173
60
West Sx RH
Considering you don't ride in the rain or mud, it should be spotless plus you have a fetish of opening it every week.
 

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
that is only the 2nd time i have opened it from day one i put grease over both bearings as back then you never got that plastic protector to cover the right hand side bearing.

and the lock ring was plastic as well lol, but if you do remove the cover be carful not to damage the seal top left around the outside of the cover or put some grease around the outside so nothing can get inside ;)
 

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
DSC_0126_04.JPG


thought i had a socket big enough to fit over the crank shaft but no and 1 size to small. :rolleyes:

DSC_0127_03.JPG

DSC_0128_03.JPG

that should work ;)
 
Last edited:

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
peter saves the day yet again as the torque sensor security bolt was ceased solid and would not budge with the 17mm socket i got to remove it as just slipped so plan b was drill some holes in it to try to use my circlip plyers and broke the end of one of those so plan c out comes the Dremel and grind a lip in to it so can take it out with a hammer and screwdriver and bingo but the nut is totaled.

DSC_0129_03.JPG

DSC_0130_02.JPG

i need to remove that nut so can get the crank shaft out so i can check the circlips are still in place as one on the left side could be broken and wearing the nylon transfer gear.

to be continued ;)
 

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
DSC_0144_03.JPG

pretty much the last part i can upgrade to with the cx motor and super fast postage from peter
@www.ebikemotorcentre.com/ :cool:
 

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
just a warning to anyone getting one of these displays even tho it can do some updates via the phone it is still asking to be taken to a dealer for a update :rolleyes:

it goes away in 2-3 seconds and bike works as normal but shows that msg every time you turn on the display.

and it has some how turned on emtb mode :rolleyes:
 
Last edited:

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
DSC_0145_03.JPG

well that just looks shite so the stem mount is going to be replaced with one of these to get it out of the way.


45324
 

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
DSC_0146_03.JPG
DSC_0147_03.JPG

well according to that i cant go faster than 16mph :D
 

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
DSC_0149_03.JPG
:cool:
 

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
DSC_0154_02.JPG

if you use komoot and link the accounts it does show the correct speed on that :cool:
 

soundwave

Esteemed Pedelecer
May 23, 2015
15,973
6,292
DSC_0167_03.JPG
eagle sprocket.


DSC_0168_03.JPG
normal sprocket.
 
Last edited:
  • Like
Reactions: gramorganic

Related Articles

Advertisers