Search results

Fwiw my approach would be a google image search for the brand of controller and the keyword "pinout" Below the battery phase and motor sensor wires separated to the top of the image, you have the plug with the blue/white wires coming out into a seperate plug, this i suspect is the key switch...

One of the features of the KT controller range is the ability to use a number of different interface devices, and when a lcd dispaly is used you can also use it to configure and check the controller status, as well as get error codes in cases of failure.. It might be prudent to get a kt lcd...

Starting upwards on an incline Is the worst possible scenario for an ebike, and will stress/tax the motor the hardest/worst. but as long as your pedaling in a low enough gear to rotate the pedals easily the assistance should be noticeable and helpful!.. Even so your initial reaction to a new...

Just be mindful some hubs have speed and hall sensors fitted others just hall sensors and some are sensorless, If not explicitly stated the number of connecting wires is a good indicator, 9 wires = 3xphase wires +5v ,ground(to supply sensors with power) , 3x hall sensor outputs and 1 x speed...

glws to sell to a wider area consider packing and shipping in a bike box.. youtube has videos detailing the short procedure its a 10 minute job to remove pedals front wheel and loosen the handlebar stem.. and shipping firms sell boxes for bikes with all packing foam etc needed as a bundle for...

Yikes! not what you wanted to find under the old holder.. grinding it down would be my last option tho, where abouts on the new slide is it obstructing, while a clear pic of the 'nub' its not clear where on the tube its sitting..

Indeed the brake lever motor cut off is an instant OFF for the motor while there is a delay between stopping pedaling and the motor cutting off. Also negotiating obstacles in the rd can sometimes benefit from cutting the power momentarily while you snake past obstructions where power from the...

In addition to the controller/display you will also want a pas cadence sensor, and probably at least one brake sensor, to kill the motor when brakes are applied. an additional wiring loom to extend controller connections to the handlebars may also be required. some pas sensors can require the...

@about 2 1/2 mins thet describe the power port. and why you should not undo the screws beside it ;)

130+miles 'in the tank' !! Now your talking..

While waiting for your own post to get approved.. If your battery is still under any warranties. same as above applies ;). chase those down first...

Yes as long as the draw from the rear lamp is just a few ma, I had a quick scan of the ebay ad and failed to see any watt or a/ma rating for the lamp? have you measured the load?? or did i miss it? And as long as the total draw once the leds have warmed up is less than the controllers light...

:) cleaning, filling the holes with plastic putty and re-drilling central pilot holes Works!!!!! Plastic putty arrived this morning and a quick fit later im very happy and have put in an order for the full set of replacements.. Working the putty just as its cured at the 20 min mark means its...

Welcome, Wisper have manuals on the site you may need to delve deeper for older models?? If no joy there post pics of the brakes you want to adjust and their levers.. IF no one from Wisper has dropped in here by monday pm to respond to the display probs, drop them an email or call them...

Cheers @lenny on reflection it was the bathroom window locking/latching mechanism which also needed complete replacement due to rust that was the tricky element to source last time round, i recall the hassle and not the detail so much ;). What threw me with this job was the multiple...

Thanks.. I looked into it a Long time ago, my roof /house faces almost dead east and was initially advised only the south facing slope of the roof was suitable for panels. As any panels on the east or west facing slopes would only work in the morning or afternoon?? Thus at the time the benefit...

Yes BUT you need to be mindful of the current limit of the transistor switching the light circuit on and off. If you attempt to draw more current than the transistor can handle you risk blowing it and any knock-on or side effects that may have on the controllers performance. Its a lot safer...

Investigation will probably require you to start by checking the voltage of the batteries cells which would void any warranties outstanding, so if still under warranty i would request advice from the supplier to start with..

DOH!! must have overlooked that in my state of confusion.. After searching for strong plastic fillers, and getting past the modeling clays, i found JB-Weld Plastic Putty, cures in 20 mins once mixed which was a concern with standard jb weld with its 24hour cure period. superglue+baking powder...

Cheers, I have watched a few youtubes.. the problem is the frames have 2 sets of hinge screw holes already?? bad 1st fit?? and the usual technique of fitting to the corner edge requires new holes/screw positions that will result in zero support/holding capacity without repair of the upvc or...