Search results

Mosfet test . Problem I need help please . which probe do I use for power wires? red Probe or black probe. Because If I use red probe on the black and red controller cables then reading of 1 is on The red . If I use black probe on power cables then reading of 1 is on theblack . Think I’m doing...

Mosfet test . Problem I need help please . which probe do I use for power wires? red Probe or black probe. Because If I use red probe on the black and red controller cables then reading of 1 is on The red . If I use black probe on power cables then reading of 1 is on theblack . Think I’m doing...

So still all 41s even though I have a throttle ??

Bit confused by that one Nealh . Fit 3 ss41? No 49s at all ? Just to be sure you realise that the 49s were fitted by guy after drop out. but he guessed . No idea which sensors were there before. I do have a throttle

Ok back to basics . Where’s the release tabs on this kind of connector

I think all answers in my later posts but to summarise cut and repaired immediately outside hub . Inside intact and anyway Ive done continuity And passed . No other test or Repair except the attempt on the sensors and R2 Thanks

Thanks . Hope you’ve seen my last posts . There was almost def a short on the cable just outside the hub the small wires

Look let me provide more history . the bike is a giant suede . It had a change to the voilamart kit as apparently the original had a controller problem . Who did the upgrade ? No idea I bought it from the person after he guy that upgraded . Why did he install it that way ? No idea What do I...

All of you need to know that it was a relatively gentle drop out I was only walking it off the kerb . And the wiring was twisted a little . There was no major tug that would have affected the cable inside the hub the cable is do tight fitting through the axle . And I learnt that he found...

Read my posts. Bring yourself up to date. Other guy did find source if a short and repaired them so 10 points to you . Please can we move on now . I work all day . I’m at a stop cos I want to be sure of the cables to be tested fir mosfet check . I’ve posted photo but no reply yET

I don’t mind trying even if I don’t get anywhere but I believe I will . But the case as we’ve now discovered that there were 3 wires with split insulation so almost def a short.

So to all concerned with apologies again . There would definitely have been a short as he repaired 3 wires with split insulation.

I’m talking about the mosfet test As per your link sent to me . not the overall cable test Which is Already done so Like in the photos on the link it’s green blue and yellow tested against the black and red . So Is my photo the correct ones

Really sorry about this folks but I just discovered from the original guy that he did find a break and repaired them . Sorry but he only told me he tidied them up , I just thought I’d recheck with him and he said there was a break . So anyway on to the mosfets but query outstanding on that job...

So are the 2 Arrowe sets of wires the correct ones fir mosfet Tests . It looks like It as per the link given ?

Wheely I’m talking about mosfet test not Cable continuity . I’ve already done that . It doesn’t look like that in the link I was given For mosfets

I definitely will . And it’s a good way to learn from other people mistakes . I’m a quick learner and with my good sense of logic and you good fellows advice I’ll try . Only thing g working against me is free time . I’m very busy with my work . That’s why I may appear impatient for quick replies...

You’ve lost me . I’ve done the bloody continuity tests . All passed . I’ve done the cross wire tests all passed. All as advised by you . Now it’s mosfet tests when I can get to it . And when somebody answer my last questions about mosfets . I’m a quick learner and Ill know when I’ve reached my...

Well I may take on the challenge of repairing the board after I’ve checked the mosfets and double checked and jiggled the wires . After all if I don’t try I’m still gonna have to remove it for the new board. If I do I assume I have to remove the top layer to bridge a wire across Thanks

Can I just please make sure that these are the cables that I am continuity testing ?