Search results

If unsure go the whole hog and buy a new battery and a rack, transplanting/placing the controller in the front section . 36V 48V 13Ah 20Ah 500W 1500W LED Rear Rack Lithium Battery For Electric Bicycle | eBay 36V 13Ah E-bike Battery Bicycle W/ Rear Carrier Rack Bracket Fit Motor 36V 500W | eBay...

The battery case is one of a generic type for a rear carrier so chances are one will find a very similar one on ebay or look at yose bikes , Devron is just a a brand name for the bike and not the battery.

Show us a pic .

Yes, all good to go.

Yes , I said as much in #1 . Other wise how do you think you will get a voltage reading ?

Gnd is ground and Black is Ground / negative , though it doesn't matter with probes as all you will see if wrong is a -5v instead of 5v. V---- 20 range lhs of dial.

Likely #14 is low approx. 2.7 - 2.8 volts and the reason why the BMS doesn't switch. With the other cells at 4.1v it makes sense that #14 is low, one needs to try and get a correct reading for #14. Can you not probe directly on the cell group ends rather then the wiring ? One can also get a...

Yes correct Flecc , I should revert back to saying d8veh instead of plain d8ve.

As I metioned d8evh/vfr is on the forum and posts but not as much as previously, the alias used is one that belonged to a late friend of his.

If you have brake sensors then they should prevent power and accidental run on, however some controllers can vary with run on. The KT controllers I use are good and have no over run nor do I have brake sensors fitted.

Not really like a lot of folk , footy holds very little following from me.

One can use a few differing sq taper cranks. I use a pair of E6000 cranks on my bike, though had to shave 3mm off the inside boss's for a tighter taper fit. FSA CK220 JIS as used on Yamaha pw -e bikes. BBS cranks. tsdz tsdz2b TONGSHENG 170mm crank for tongsheng TSDZ2 electric bicycle mid motor...

I don't know, tbh I haven't even thought about WR as being D8veh not that it matters. Some of us though know another alias being used.

A run of the mill expected score against an inferior team, a bit of sloppy defending gifted two goals for them. That said a quality striker may have scored two more against us. Sadly the days are gone where the game offers much real interest for me.

Keplers device had a quite heavy sprung mechanism to force it on the tyre and devised the cable retention system to extend range mainly for longer rides , hills & headwinds for the dry seaon in Aus, he readily admitted it's wet weather down fall capability though wasn't his main concern for his...

Still uses a traditional rear drop out, other wise not to different to a cannodale lefty design. Cannondale being the only large producer employing the lefty fork, though MB used it's conception well before them on his prototype and low production run of bikes. The 8 freight being a prime...

On ES , Aussie Kepler used a lever and cable to actuate his friction drive kit. Kepler Friction drive comes of age. - Page 17 - Endless Sphere (endless-sphere.com)

Yes direct charging via the discharge connection but only for 10/15 secs to shock the system , of course polarity has to be correct and an adapter from charger to battery made up.

Whether a battery can be charged via the discharge wiring depends on the mosfet type used. P types aren't for reverse charging whilst N type are. One can apply a 10/15 sec reverse charge to try and wake up a BMS or disconnect & re connect the multi wire jst connection . A few reasons not...

Just got in from work so not seen the updates until now, as I said earlier and as D8ve has also reiterated the cell pack appears fine. We need to see the actual 14 voltage readings in writing. 56.6v / 14 = 4.04v each which is pretty good, with 56.6v if a cell group was 0 then the others would...