Search results

  1. J

    For Sale Giant Stance E+ 2 Full Suspension EMTB with upgrades & spares

    JPGiant submitted a new listing: Giant Stance E+ 2 Full Suspension EMTB with upgrades & spares - Giant Stance E+ 2 Full Suspension EMTB with upgrades & spares Learn more about this listing...
  2. J

    For Sale OXYGEN S-CROSS ELECTRIC MTB with UPGRADES & SPARES

    JPGiant submitted a new listing: OXYGEN S-CROSS ELECTRIC MTB with UPGRADES & SPARES - OXYGEN S-CROSS ELECTRIC MTB with UPGRADES & SPARES Learn more about this listing...
  3. J

    Storing bike for winter

    Thanks everyone, I don't use the bike in bad weather, just prep it for 'winter' and leave in the shed till Spring, battery in the house. I'll give the chain/RD & sprockets a good clean and wax this weekend.
  4. J

    Storing bike for winter

    Thanks for the replies guys, I've got some sticky motorcycle chain wax lube I might try if no further ideas.
  5. J

    Storing bike for winter

    Before the really bad weather arrives I’m considering what to do with the bike over winter particularly with regard to the chain. In the past I’ve done a complete clean/maintenance job on the bike but on the odd occasion come Spring I noticed the chain had some tight links, usually from around...
  6. J

    Half twist throttle problem

    Solved Following on from the above posts I have finally managed to install the half-twist throttle to the Oxygen MTB. As per saneagle's suggestion I cut-off the 3 pin female connector from the half-twist and tested for 5v, ground and signal wires with a 3 AA battery box power supply. Not...
  7. J

    Half twist throttle problem

    Many thanks - again.:)
  8. J

    Half twist throttle problem

    Without cutting the wires, does anyone know which of the pin holes in the throttle female connector is the +5 volts and the negative relative to the notch in the yellow plug? How do I use a multi-meter to check this please.
  9. J

    Half twist throttle problem

    Thanks for that saneagle. That could be my mistake, I thought it meant the location of the pins relative to the notch in the yellow plastic not the +, -, signal wires, bad assumption by me that all Julet connectors are wired the same. Looks like a cut and solder job then, thanks.
  10. J

    Half twist throttle problem

    To help my aging thumb I decided to swap the existing thumb throttle on my Oxygen MTB to a Half Twist version. Installtiion was easy, simply removed hand grip and fitted the new throttle, disconnected the original throttle connector (a Julet version) and connected the new one, also a Julet...
  11. J

    Cyclotricity Crank Drive BEAST 250W/500W Electric Mountain Bike

    Hi All Has anyone got/had or tested one of the above bikes? I'm looking for opinions, reviews do's and don't's before I contact them. I understand the above model comes with the motor set at 250W, I'm not looking for any more to keep within the UK regs. I've read so many conflicting reviews on...
  12. J

    You get what you pay for!!

    I think it would help (others in particular) if you were to name the bikes you mentioned in your original post. Otherwise it's reads like a rant without substance, despite all the highly respected responses from some other ebike owners. Name and shame, or praise with pride.
  13. J

    Short Julet extension cables.

    I had a similar problem some time ago. ended up buying the longer ones and cutting them in the middle, shortening to required length and re-soldered each wire with shrink wrap over each, then a larger shrink wrap over the whole cable. Other, cheaper option is to loop the excess cable and...
  14. J

    Oxygen battery

    Is this what you're after... BATTERY They're Oxygen stockists
  15. J

    S-Cross Central Display Oxygen ebike.

    This LINK may help... page 11 states "The display panel will go into sleep mode when the speed is 0 Km/h for 5 minutes" Is the display backlight On/Off?
  16. J

    Help with problem

    Get a new one HERE...
  17. J

    Help with problem

    Also, make sure you release the front caliper, this may be binding/preventing the wheel from dropping into the forks properly. Then reset it.
  18. J

    Help with problem

    Undo the QR axle, hold the wheel/tyre near the uneven gap on the forks & pull gently to even out the gaps. Re-tighten the QR.
  19. J

    Oxygen ebike

    Contact Oxygen direct.
  20. J

    Oxygen ebike

    Surprised you didn't get a user manual with the bike, still, from Oxygen website, here goes ... USER MANUAL