Search results

Re points above, if I can remember in my case, the front 250w only was sold as legal (or can be made legal), not the rear 350w. The reason (in my case with kt controllers and probably the same with you) the front and rear controllers are not interchangeable is because of the front light on the...

My daughter has a electric pendleton and I have assembled a number of flat packed Halfords bikes. They all come with literature explaining why the frame guarantee on aluminium frames is much shorter than the 10 year given on their steel frames. My daughters 2017 pendleton came with a 38T front...

My daughters Pendleton (2017 Halfords) came with a Phylion Battery with 'smart BMS' which featured a 'coloumb counter' that is suppose to give an accurate reading. However, (according to instructions) the battery needed to go through a couple of charge/discharge cycles for this to calibrate/work...

All the setting are stored in the LCD. The LCD communicates with the control and downloads all the settings continuously to the controller. The controller copies those settings that are relevant. So the settings are stored in both the LCD and the relevant ones in the controller. This allows the...

I keep using rim until wear indication line disappears entirely or rim wall start to splay outwards sometimes causing a pulsing that can be felt in the v brakes. Attached below old article with same idea as yourself but mainly refers to rims without wear indicator.

My daughter has a ladies Pendleton ebike bought from Halfords in 2017 with similar 790 unit. I'm not sure exactly where I got the codes as it was a few years ago but if you Google 'King meter 790 manual', there are updated versions/variants available.

790 display. The fault code are as below. Light Combination Definition indicator light flash(LOW level) abnormal current level indicator light flash(MED level) abnormal throttle level indicator light flash(LOW+MED level) motor phase level indicator light flash(HIGH level) Motor hall...

Some simple user checks/tests that can be done. 1.Make sure that motor is not disabled in lcd and use + button to set eco/tour/speed/turbo. 2.Disconnect brake cutoff cables at back of lcd and recheck. 3.Disconnect throttle. Does motor work when pedaling i.e. with torque sensor? 4.Enable walk...

Dont use 12g spokes (imo) as I had to drill the rims spoke holes wider and in the direction of spokes when replacing rims lately. (The wheels were originally built with 12g spokes) Also this is not really possible with rims with eyelets so I used plain rims. 14g as suggested by Nealh is normally...

pswpower have them (10X12mm) but delivery time could be 2 weeks. Maybe someone else might suggest a quicker/local supplier. https://www.pswpower.com/products/screw-electric-bike-parts-nuts-with-washers-electric-bike-hub-motor-axle-12mm-lock-nut-washerspacer-set-71

Attached picture. Just to clarify, I take it this is what you mean by the 'securing plate' that you intend not fitting.

Don't underestimate the torque force. A 80nm motor exerts 80 newtons pressure at 1 meter. However the motor center (and torque clamps etc) is about 70mm from center, so the potential force (tangential twisting force of the whole assembly) will be approx 15 times 80 newtons which is approx 1200...

The z bend is not stronger than the j bend and as such probably has no advantage for manufacturers/suppliers. It can still break at the ends like any other spokes but I do note that they wrap themselves around the hub flange better than some of the stainless steel 13g spokes that fatigue and...

I have made repairs with recycled/reused spokes by making z-bends (without special tools) to desired length. They have never failed. One objection to z-bends is that they clutter the ordinary smaller wheel hub but this is not a problem with large hub motors. On some motors, the holes are closer...

The 'flange offset' I think is the distance by which the spoke flange is distant from the wheel centre line. You have this wrong with the 'wheelbuilder'. Be sure to measure on the actual hub.

On the front hub dimensions (picture) you attached, the dishing offset is 'Dimension F = 8.2mm'. Also note WR =58 & WL =42, which gives the 16mm difference which requires offset of 8mm. Note that if you have to make any axle adjustments with washers afterwards ( e.g. to line up with disk brake)...

I have a 250w front cyclotricity kit (xf07 clone) bought from ebike direct (who advertised on this site) back in 2018. It came with a kt controller and throttle and a special plug that shorted the red/blue wires instead of the display. The display and pas is a rather expensive upgrade as in link...

https://www.endless-sphere.com/forums/viewtopic.php?f=2&t=104090#p1520695

Its mainly the road camber imo. One suggestion is to reverse the tyre to even the wear as the arrows have no real technical function on schwalbe road tyres. https://www.schwalbe.com/en/profil

Your bike should basically work at them settings. But I would suggest/comment the following. P2 is set for 6 speed sensor magnets. If speed wrong and wheel has only 1 magnet, set P2=1. C1 may have to be changed (e.g C1=07) depending on PAS type fitted. C4 = 4 means the throttle is...