Search results

I put a Suntour NCX on my Titanium framed hardtail recently. Well worth the cost, gives a very comfortable and relaxing ride on our modern moonscape type roads.

Does anyone else have any practical examples or tests and results they have done where eBike batteries, preferably 10Ahr and less, have been discharged to say 3.0V per cell whilst measuring the Ahr capacity then charged back up to 4.1V per cell, the charge stopped, either at the first 4.1V point...

Indeed not. I have not done a discharge test using the diode charge hack, and I will wait for the 1A charger to arrive.

Especially as that price had 'free postage'

If I do that then the range covered increases dramatically, since the motor cuts out, as required, at 15.5mph.

Nope; Thre was a cheaper one, £2.56, but no longer available.

Here is a picture of a Charger you can get for those Bosch powertool batteries, its they are about £25 from the far east. The plastic bit that contacts the battery and holds it, with the 5 metal prongs, looks a slightly different colour to the body of the charger, wonder this holder is...

I will wait for the 1A charger to arrive before checking again, its good to be kind to batteries. I did see a 42V 1A charger on Alixpress for around £3 delivered, but thats too cheap to be true I think.

Here is the plot. The current drop under CV is about the same until 1Amp, but then diverges considerably.

I would take the range a seller quotes with considerable caution. Range can vary tremendously depending on the weight of the rider, the terrain (as in hills), how fast you go and how much effort you put in. So one seller quoting 40 miles for a bike does not mean it has more 'range' than a...

The charge with a Si diode in series does work and the battery charges to 41.2V or so but the constant voltage stage takes around 2 hours to complete versus about 1 hour when there is no diode and the battery charges to 42V. This is a 5Ahr battery pack and charging at 2A is a bit much for long...

The connector I am not sure about, however I am interested in the use of the Bosch powertool batteries on a Brompton. I have recently converted a Brompton to electric and using a 10S1P Samsung 21700 battery I ended up with a working eBrompton weighing in at 11.8Kg. The 5Ahr battery I have...

The significant problem with chairs like that is that they cannot cope with soft ground, the legs are only suited to firm ground. One easy low cost solution to this would be plastic plates maybe 15cm diameter which you could put on the legs to stop them sinking. The mat under the legs on the...

Dont see the logic of that, charging to 42V and then discharging to 41V, is just not the same as charging to only 41V. No hack to a charger needed, just make up an Anderson lead with a diode in-line to go between charge monitor and battery.

I had thought of that, and tried it, but on the charger I was using, my original Swytch Brompton one, the charger did not detect the battery, so I did not try any further. I suspect this charger does not turn on until it sees the battery, and with the diode in place there is no battery voltage...

Can you tell us which canal you live next to ?

Indeed, the nylon mat bottom of the OEX, is a key factor in stopping the legs dissapear into soft ground.

Ask your local Council, they may take them for free. Dont sell it on eBay.

Try one of these Ultralight chairs, small when packed, 35cm long x 10cm diameter, 1.2Kg. Very comfortable. Not as easy to assemble as a standard folding camping chair, but then they weigh a ton and are huge packed.

I used to take somthing very similar out when walking in the hills, agreed, well worth the few grams. But I also cheated a bit, I cut up the ground sleeping mat you would normally take camping, into 3 pieces, joined it with gaffa tape and used it (folded) as a liner for the back of my rucsac. I...